C.13 Package loading messages.

This section lists all messages that can occur when the compiler is loading a package from disk into memory, saving a package from memory to disk or when parsing packages in general. Many of these messages are informational messages.

Fatal error 13001: Can’t find package 〈arg. 1⟩

You tried to use a package of which the PCP file isn’t found by the compiler. Check your configuration file for the package paths.

PCP file for package 〈arg. 1⟩ found

The PCP file for the specified package was found.

Error 13003: Duplicate package 〈arg. 1⟩

The package was already specified as required package and may not be specified a second time.

Error 13004: Unit 〈arg. 1⟩ can not be part of a package

The unit can not be part of a package because the DenyPackageUnit directive is enabled for the unit.

Note 13005: Unit 〈arg. 1⟩ is implicitly imported into package 〈arg. 2⟩

The unit was not specified as part of the contains section and is also not included in one of the required packages. Add the unit to the contains section to increase compatibility with other packages.

Fatal error 13006: Failed to create PCP file 〈arg. 2⟩ for package 〈arg. 1⟩

The PCP file for the package could not be created.

Fatal error 13007: Failed to read PCP file for package 〈arg. 1⟩

The PCP file for the package could not be read.

PCP loading 〈arg. 1⟩

When the -vt switch is used, the compiler tells you what packages it loads.

PCP Name: 〈arg. 1⟩

When you use the -vu flag, the package name is shown.

PCP Flags: 〈arg. 1⟩

When you use the -vu flag, the package flags are shown.

PCP Crc: 〈arg. 1⟩

When you use the -vu flag, the package CRC check is shown.

PCP Time: 〈arg. 1⟩

When you use the -vu flag, the time the package was compiled is shown.

PCP File too short

The PCP file is too short, not all declarations are present.

PCP Invalid Header (no PCP at the begin)

A package file contains as the first three bytes the ASCII codes of the characters PCP.

PCP Invalid Version 〈arg. 1⟩

This package file was compiled with a different version of the compiler, and cannot be read.

PCP is compiled for another processor

This package file was compiled for a different processor type, and cannot be read.

PCP is compiled for another target

This package file was compiled for a different target, and cannot be read.

Writing 〈arg. 1⟩

When you specify the -vu switch, the compiler will tell you where it writes the package file.

Fatal error 13019: Can’t Write PCP-File

An error occurred when writing the package file.

Fatal error 13020: Error reading PCP-File

This means that the package file was corrupted, and contains invalid information. Recompilation will be necessary.

Fatal error 13021: Unexpected end of PCP-File

Unexpected end of file. This may mean that the PCP file is corrupted.

Fatal error 13022: Invalid PCP-File entry: 〈arg. 1⟩

The unit the compiler is trying to read is corrupted, or generated with a newer version of the compiler.

Trying to use a unit which was compiled with a different FPU mode

Trying to compile code while using units which were not compiled with the same floating point format mode. Either all code should be compiled with FPU emulation on, or with FPU emulation off.

Packagesearch: 〈arg. 1⟩

When you use the -vt option, the compiler tells you where it tries to find package files.

Required package 〈arg. 1⟩

When you specify the -vu switch, the compiler will tell you which packages a package requires.

Contained unit 〈arg. 1⟩

When you specify the -vu switch, the compiler will tell you which units a package contains.

Error 13027: Unit 〈arg. 1⟩ is already contained in package 〈arg. 2⟩

A unit specified in a contains sections must not be part of a required package. Note that a unit might have become part of another package by indirectly including it.

Warning 13028: Unit 〈arg. 1⟩ is imported from indirectly required package 〈arg. 2⟩

If a unit from a package that is not part of the requires section is used then the package should require this unit directly to avoid confusion.

PPL filename 〈arg. 1⟩

The name of the binary package library that is stored in the PCP.